Professional heating, cooling & air quality services serving Pullman and surrounding communities in Washington. NATE-certified, 24/7 emergency response.
From emergency repair to planned installation, we deliver expert HVAC service across every specialty.
Replacing an aging HVAC system with properly sized, high-efficiency equipment can reduce energy costs by 30 to 50 percent. Professional installation covers equipment selection, ductwork modifications, refrigerant line installation, electrical upgrades, and thorough commissioning to verify rated SEER and AFUE output.
Properly sealed and insulated ductwork is essential for delivering rated BTU output to every room in your home. Our technicians repair collapsed sections, seal leaks with UL-listed mastic and mechanical fasteners, and verify balanced airflow across all supply registers after service.
Indoor air quality suffers when ductwork harbors years of accumulated particulate matter, allergens, and biological growth. Thorough duct cleaning addresses every branch run, main trunk line, and register boot using agitation tools and high-powered vacuum extraction to restore clean airflow.
Professional AC tune-ups follow a multi-point inspection protocol covering thermostat calibration, condensate drain clearing, electrical connection tightening, and evaporator coil cleaning. Maintaining clean coils and proper superheat readings keeps your system running at peak rated efficiency.
Clogged dryer vents are a leading cause of residential fires, with lint buildup restricting exhaust airflow and causing the dryer to overheat. Professional cleaning removes compacted lint from the full vent run, verifies proper airflow velocity, and inspects the exterior termination for damage.
Whether you are purchasing a home, preparing for seasonal demands, or evaluating replacement options, a thorough HVAC inspection provides actionable data. Technicians measure airflow, test safety controls, assess AFUE and SEER performance, and deliver a written report with prioritized recommendations.
Smart thermostats from Ecobee, Nest, and Honeywell Home offer occupancy sensing, geofencing, and learning algorithms that adapt to your schedule automatically. Our technicians verify system compatibility, install the required wiring, and configure the device for optimal interaction with your specific HVAC equipment.
Installing a mini-split system correctly requires precise wall penetration, vacuum-sealed refrigerant lines, and proper electrical isolation between indoor and outdoor units. Our technicians size each zone independently using BTU calculations to ensure consistent temperature control across every room.
Heat pumps rely on a precise balance of refrigerant pressure, electrical components, and airflow to deliver efficient heating and cooling year-round. Professional repair addresses compressor hard starts, frozen coils, faulty thermostatic expansion valves, and auxiliary heat lockout conditions.
Preventive furnace maintenance protects your household by identifying cracked heat exchangers, carbon monoxide risks, and failing ignition components before they cause a breakdown. Annual service preserves rated AFUE efficiency and ensures consistent airflow through cleaned blower assemblies.
When your AC blows warm air, short cycles, or fails to start, the problem may involve a failed compressor, low refrigerant charge, frozen evaporator coil, or faulty control board. Professional repair identifies the exact fault and restores rated SEER efficiency through precise, manufacturer-guided procedures.
Upgrading to a modern heat pump delivers dual-mode heating and cooling from a single system, with top-tier models achieving 10+ HSPF and 20+ SEER2 ratings. Proper installation includes Manual J load calculations, refrigerant line sizing, and electrical panel verification for reliable year-round comfort.
Boiler systems demand specialized knowledge of hydronic circuits, expansion tanks, pressure relief valves, and combustion analysis. Our technicians diagnose issues ranging from kettling and low water pressure to faulty zone valves and circulator pump failures across gas, oil, and electric units.
When a mini-split displays error codes, produces weak airflow, or fails to reach setpoint, the fault often lies within the inverter board, thermistor sensors, or refrigerant circuit. Professional repair restores rated SEER output and eliminates the inefficient short cycling that drives up utility costs.
When your heating or cooling system fails unexpectedly, rapid diagnosis is critical to minimizing discomfort and preventing secondary damage like frozen pipes or heat-related illness. Emergency technicians isolate the fault, whether electrical, mechanical, or refrigerant-related, and execute repairs on the spot.
Pullman, WA is home to 33,886 people and a wide variety of heating and cooling systems — from central forced air to radiant boilers to ductless mini splits. KIC Refrigeration has worked on every HVAC configuration across the Pullman area. That hands-on experience means we know exactly which equipment brands and installation methods deliver the best performance in this region.
Our familiarity with Pullman extends beyond HVAC equipment — we understand the neighborhoods, the local permitting process, and the seasonal weather patterns that stress every heating and cooling system in the area. When KIC Refrigeration takes on your project, you benefit from a team that factors in your home's age, insulation quality, and duct layout before recommending a single piece of equipment.
Built on NATE certification, transparent pricing, and a guarantee that we stand behind.
Every technician on our team holds current NATE certification — the highest standard in the HVAC industry for installation and service competency. You get a technician who has passed rigorous exams on system diagnostics, refrigerant handling, and equipment commissioning.
You receive a written estimate with itemized parts and labor costs before any work begins, and the final invoice matches. No diagnostic fees hidden in the repair bill, no surprise surcharges — just honest pricing you can verify and trust.
HVAC failures do not wait for business hours and neither do we. Our emergency technicians are dispatched around the clock — nights, weekends, and holidays — so you never go without heat in winter or cooling in the peak of summer.
Our technicians live and work in the communities they serve. They understand local building codes, climate demands, utility rebate programs, and the HVAC challenges specific to your area. Local expertise backed by a nationwide service network means fast response and consistent quality everywhere.
Every technician carries EPA Section 608 Universal certification for refrigerant handling — required by federal law for working with R-410A, R-22, R-32, and all regulated refrigerants. Your system is serviced by technicians who handle refrigerants legally and responsibly.
Answers to the heating and cooling questions our customers ask most often.
Heat pumps offer both heating and cooling from a single outdoor unit, making them significantly more energy-efficient than furnaces for moderate climates. A heat pump does not generate heat — it transfers it from outdoor air, which requires far less energy than burning gas or running electric resistance coils. Modern cold-climate heat pumps with variable-speed inverter compressors operate effectively down to minus 15 degrees Fahrenheit, making them viable in most Washington locations. For Pullman homeowners with natural gas access, a dual-fuel system — heat pump for primary heating paired with a gas furnace for backup during extreme cold — often provides the best balance of efficiency and performance. Heat pumps also qualify for federal tax credits under the Inflation Reduction Act. KIC Refrigeration evaluates your specific climate zone, insulation levels, and utility rates to determine whether a heat pump, furnace, or dual-fuel system is the smartest investment.
KIC Refrigeration installs and services all major HVAC equipment manufacturers in Pullman including Carrier, Lennox, Trane, Daikin, Goodman, Rheem, York, Bryant, American Standard, Mitsubishi, and Fujitsu. For ductless mini split systems, we specialize in Mitsubishi, Daikin, and Fujitsu units which are the market leaders in inverter-driven technology. We are not locked into a single manufacturer or distributor, which means our recommendations are based entirely on what best fits your home size, budget, efficiency goals, and existing infrastructure. Each brand offers different warranty structures, SEER2 ratings, and feature sets — from basic single-stage units to premium variable-speed communicating systems. Our NATE-certified technicians install every unit strictly to manufacturer specifications and register all warranties on your behalf.
Most residential HVAC installations in Pullman, WA are completed in 1 to 3 days depending on the system type, condition of existing ductwork, and complexity of the project. A straightforward furnace and air conditioner replacement on existing ductwork typically takes a single day — our crews arrive in the morning and commission the new system by afternoon. Heat pump conversions, ductless multi-zone installations with line sets routed through walls, and projects requiring new or modified ductwork may take 2 to 3 days. Commercial installations and whole-building systems can extend to a week. We schedule around your availability, coordinate all permits and inspections, and protect your flooring and walls throughout the process. Every installation concludes with a full system commissioning including airflow verification and refrigerant charge confirmation.
A comprehensive HVAC inspection from KIC Refrigeration in Pullman covers every critical component of your heating and cooling system. Our NATE-certified technician evaluates the heat exchanger for cracks using a combustion analyzer, checks thermostat calibration and wiring, tests all electrical connections for tightness and amperage draw, measures refrigerant pressures against manufacturer specifications, clears the condensate drain line, inspects the blower motor and fan assembly for wear, checks the air filter and evaporator coil condition, tests safety controls including high-limit switches and flame sensors, performs carbon monoxide testing on gas-burning equipment, and measures supply and return airflow temperatures to verify the system is producing its rated BTU output. We also visually inspect accessible ductwork for leaks, damage, and insulation condition. You receive a written report with all findings, photos of any concerns, and prioritized recommendations.
The ideal time for HVAC replacement in Pullman is during the shoulder seasons — spring and fall — when demand is lower, equipment availability is highest, and scheduling is more flexible. Contractors are less booked during these periods, which means faster installation timelines and potentially more competitive pricing. You are also more likely to find manufacturer rebates, utility incentive programs, and promotional financing during off-peak months. From a technical standpoint, moderate temperatures allow your new system to be commissioned and tested under less extreme conditions. However, KIC Refrigeration completes HVAC installations year-round in Washington and can often start within days of your approved estimate, even during peak summer or winter demand. If your current system is showing signs of failure, do not wait for the perfect season — a planned replacement is always better than an emergency one.
Most HVAC installations, major equipment replacements, and significant ductwork modifications in Pullman require a mechanical permit from the local building department. This applies to furnace and air conditioner replacements, heat pump installations, boiler swaps, and new ductless mini split systems. Minor repairs like part replacements and refrigerant recharges typically do not require permits. KIC Refrigeration handles all permitting, code compliance documentation, and scheduling of final inspections on your behalf — you do not need to visit any government office or coordinate with inspectors. Permits exist to ensure your system is installed safely and to code, which protects your home and preserves your equipment warranty. Unpermitted work can create liability issues and complicate future home sales. We ensure every project meets current Washington mechanical codes and International Mechanical Code standards.
Our reputation is built on honest service, skilled technicians, and systems that perform.
"Furnace tune-up was straightforward and the technician was friendly. Gave some tips on filter replacement schedules which was helpful."
"KIC Refrigeration installed our new heat pump system and the difference is incredible. Our energy bills dropped noticeably the very first month."
"Good experience with the air duct cleaning. Two-person crew was efficient and professional. The house smelled fresher right away."
We also serve these nearby communities with the same certified HVAC expertise.